Connect the incoming antenna wire to a two-way signal splitter. If you're using flat-lead wire, use an adaptor to convert it to coaxial cable and use a standard cable splitter.
How to Get a Local FM Radio on a TV Antenna
Attach one new cable to the splitter and run it from there to your TV or set-top box and reconnect it. Attach another to the splitter's second output and run it to your FM radio or your stereo receiver. Thread the end of the cable onto your radio or stereo's FM antenna input or use an adaptor to convert back to screw terminals. Turn on your stereo and check the reception on your preferred stations. Adjust the direction of your antenna to find a compromise, if needed, between TV and FM radio reception.
Fred Decker is a trained chef and certified food-safety trainer. He's held positions selling computers, insurance and mutual funds, and was educated at Memorial University of Newfoundland and the Northern Alberta Institute of Technology. Tips Although your television signal passes through the wire as an electrical impulse, it's too small to pose a shock hazard. You won't need to unplug or turn off the TV or radio, but you should turn the volume to zero to prevent any risk of damaging the speakers while you're connecting to your antenna.
If your TV and radio both have screw terminals for twin-lead wire, this type of splitter is more difficult to find.
- How Radio Works!
- hookup tacoma?
- Connecting an FM/AM antenna AVR-XW.
If your equipment has cable-type connectors, use a standard cable splitter and buy adaptors to convert your twin-lead wire to coaxial. If your antenna is amplified, or if you use an inline signal amplifier, radio stations may sound very noisy and irregular. Switch the amplifier off, and see if the sound improves. This wikiHow teaches you how to create your own FM antenna in order to increase your FM receiver's range. Depending on your preferred range, you can do this by using either coaxial cable or speaker wire.
This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Gather the necessary materials. In order to make a vertical antenna from a coaxial cable, you will need the following materials: Calculate the length of your antenna. This will determine both how much of the coaxial cable you have to strip and how long your copper tubing should be: Divide by the frequency to which you want to connect e.
Can someone show me how to hook up an FM antenna? Please!
Divide the resulting number by 2 e. Multiply the resulting number by 12 inches to find the antenna length e. Cut off one end of the coaxial cable. While you'll want to leave one end of the coaxial cable intact in order for it to serve as the connector, the other end will need to be removed. You can use your wire cutters or a hacksaw to do this. Strip half of the antenna's overall length from the end of the coaxial cable.
You'll need to remove each layer of shielding until you arrive at the white layer surrounding the coaxial cable itself. For example, if your antenna is supposed to be six inches per your calculations, you'll remove three inches of shielding. You'll need to remove the copper shielding during this process.
AM loop antenna assembly
The easiest way to do so is by making a shallow incision with the hacksaw all the way around the shielding and then attempting to strip it off from there. Cut the copper tubing to half of the antenna's overall length. The copper tubing will comprise the other half of your antenna's receiver, so it should be the same length as the section that you just stripped. Again, if you're using a six-inch antenna, the copper tubing will be three inches. Attach the tube to the coaxial cable. Slide the copper tubing onto the coaxial cable's stripped end, then slide it down to the.
Solder the coaxial cable's shielding to the tubing. You can do this by removing the PVC black shielding from around an inch of the coaxial cable directly below the unshielded part, peeling it back with a pair of pliers to form a lip, and then using your soldering pen to connect the lip to the copper tubing.
How to Hook an Antenna Up for a Panasonic Radio | It Still Works
Connect the coaxial cable to your audio receiver. The remaining coaxial connector should plug into the receiver's coaxial antenna port, which makes the rest of the antenna placement fairly simple. Once the antenna is plugged in, angle it toward the nearest station and secure it in place if necessary. The fewer obstructions between your antenna and the nearest FM station, the stronger your signal will be.
Your coaxial cable may be stiff enough to stand on its own without needing support, but you can use stables or any adhesive to prop up your antenna as needed. Understand when to use this method. If your connection to an FM station is mostly fine but requires some fine-tuning from time to time, you can use speaker wire as a quick range-extender to improve the quality of your connection.
Speaker wire is not an ideal solution to long-range issues. If you're having trouble receiving a signal at all, you should try using coaxial cable instead.
- funny dating opening lines.
- Using the AM loop antenna.
- Connecting an FM/AM antenna.
- How to Hook an Antenna Up for a Panasonic Radio.
- dating website kent.
- mkr twins dating.
- is it worth trying online dating.
In order to craft a crude antenna from speaker wire, you'll need the following items: Split three feet of the speaker wire. Using a knife or a pair of pliers, separate the top three feet of the speaker wire tubes from each other. You should be left with three feet of spit wire and seven feet of intact wire. Arrange the speaker wire to form a "T" shape.
The reason for this relationship has to do with the speed of light , and the distance electrons can travel as a result. The speed of light is , miles per second , kilometers per second.
Video of the Day
On the next page, we'll use this number to calculate a real-life antenna size. The Rolling Stones or The Beatles? History of Radio Pictures.